Dismantling the front door of a VAZ 2110

Before painting the doors, the main thing is not to forget to deal with the door hinges. By themselves, they are almost eternal if lubricated. But who lubricates them? that’s why there are problems (then you find bolts inserted instead of hinges)

So don’t be lazy, buy a can of penetrating lubricant and spray it on the hinges, they’ll last longer!

And instead of a bolt, I inserted a hardened axle (from some kind of photocopier, a scanner ruler guide, you can get these at office equipment repair shops for almost free)

Having previously made cuts for lubrication and filled with lubricant

I actually filmed the axle repair on video, watch it!

And then I tried on the door trims. The manufacturer is unknown, obviously some kind of cooperative, from the designation - the name of the door trim VAZ-2110L (probably luxury) Syzran

They look good, the quality is cooperative, but tolerable

But the problem with the fastening is that it doesn’t “dance” plus or minus from half a centimeter to a centimeter + the fasteners are of different heights.

More details in the video

And in words - I will install fasteners from the doors of the Passat B2-B4, there are convenient brackets and fastening with self-tapping screws to the end of the casing. And no breaking pistons

And the painting... I didn’t have time to prepare everything today, I was working on Confidence, come back tomorrow!)

The car is already a little over 10 years old and the hinges on the huge sliding doors are already very worn out, the doors sagged and moved up and down a lot. I have often seen on the Internet that it is possible, without changing the hinges, to replace only the fingers and the moving part of the hinge. It is recommended to use Opel fingers, because... they are stronger and less likely to get dirty. In addition to the hinges, I decided to immediately replace the locks, limiters and everything that had become unusable.

It was purchased: - Ordered with Emex fingers Opel 01 32 608 or an analogue from General Motors 90518425 4 pcs - Hinges assembled VAZ 2110 or 2108 (I took 2110 for myself) 4 pcs - Door opening limiters VAZ 2110 2 pcs - Brano door locks (only right , the left one was not found in my city.) 2 Pieces - Silent lock fingers 2 Pieces - Internal door locks 2108 2 Pieces

I didn't want to remove the doors, but I had to because... The width of the garage was enough for me to fully open the door and reach the hinges with a tool. I started with the passenger side.

Tuning

After finishing removal, clean the cards from dust using a vacuum cleaner, and begin tuning yourself.

First of all, measure and cut the necessary “patterns” for all door cards, taking into account an allowance of 5 or even 7 centimeters for each side.

This is so that during the process of gluing the sheathing material you do not have to install patches or redo everything all over again.

The glue must be applied to the cards with brushes one at a time so that it has time to dry a little, but not dry out. Having coated the doors with glue, we proceed to the cut piece of vinyl or fabric, which we also coat with glue on the back side, and set aside for 10-15 minutes.

After this time, we proceed directly to gluing the upholstery to the door cards. Vinyl stretches well, filling door “cavities”, but for this it needs to be heated with a hair dryer and smoothed over each cavity and bulge with your hands, preferably with gloves. The edges need to be carefully folded inside out and trimmed.

We subject the remaining doors to the same procedure. In addition, it is advisable to paste the same material over other parts of the interior so that it is in the same style.

These include door handle inlays, the glove compartment lid (if you want to highlight it), triangles at the mirrors, and the top cover of the steering casing. In places of various fastenings, you need to cut small holes using a stationery knife.

When reinstalling, do not forget to replace damaged pistons.

Door hinge repair options

Failure or severely deformed hinges are repaired using the following methods:

1. Complete door replacement. It is complicated by the fact that it is not always possible to find new VAZs for old ones. You have to buy old elements that are partially worn out.
2. Inserting new hinges. A good option, but you will have to make additional adjustments and eyeliner. When inserting new ones, you will need a welding machine; for cutting, at least an impact drill, but a gas cutter is better.
3. Replacing old fingers. It will only work if the hinges themselves remain intact and undeformed, and only these metal pins are bent (or come off the axis).

Replacing door hinges, as well as fingers, is the most rational option in this case. It's inexpensive and relatively easy to do. If necessary, additional equipment can always be rented at a service center or automotive supply store. The cost of the hinges themselves for the VAZ 2110 and similar models is only about 300-500 rubles. You can also find old, used ones for sale. You will have to pay less for them. But new VAZ 2110 doors will cost several thousand rubles. And they are sold, as a rule, without glass and cladding. Their installation is an additional waste of money.

How to replace door hinges on a VAZ 2110 car

If you need to replace the hinge on the front door of a VAZ 2110, then in addition to dismantling the door, you also need to remove the front fender. Then:

• A workplace is prepared, preferably a table, which is covered with a soft cloth to preserve the paintwork. This is not necessary for major renovations.

• Replacing door hinges on a VAZ 2110 begins by cutting off the old hinges at the base.
• Rust is cleaned and removed from the installation site of new hinges.
• New hinges are screwed to the car body pillar.
• The door is installed in the opening.
• Fixed in the correct position relative to the body. In this case, you need to monitor the gaps along the threshold and between the roof and the adjacent door.
• The door is pre-fixed using any method.
• The wing is put in place.
• Gaps are controlled.
• The wing is removed.
• The hinges are welded to the door.
• All additional fixations are removed.
• The correct installation of the doors is checked. To do this, you need to open and close them several times.

How to replace door hinges on a BA 2110 is clearly visible in the video.

Replacing the entire hinge

If the door is sagging, then the likely cause is deformation or mechanical wear of the hinges. It is corrected by completely replacing them, along with the fingers. You don't have to buy them. You can make it yourself if you have a metal cutting machine. Such repairs will be cheap - you will only have to pay for the purchase of high-quality metal plates.

It is recommended to cut the loops strictly along the boundaries of their wedging. Fingers are placed last. And again, you need to lubricate them, hammer them, and lock them, as the manufacturer himself recommends. Replacement without taking into account their manufacture (if you do it yourself) will take at most several hours, including removing and reinstalling the doors. All that remains is to make the adjustment. And you should understand that in the next few days the noose may fall. This is shrinkage. The door may creak and may not always slam shut normally. If necessary, readjustment is performed.

Removal

Dismantling work is the beginning of your journey to replacing the door panel trim. It's nice to know that this task is quite simple. This is especially true for the front doors.

We will tell you separately about the nuances of dismantling the front and rear door trims of your VAZ 2110.

Disassembled cards

Front

Let's say right away that the likelihood of damaging the standard clips is very high. But this is not scary, since new products are cheap, and their installation is much simpler than repairing old caps.

If you are installing Euro panels, you will have to remove the lever from the window regulator.

The process is performed according to a certain algorithm:

• Using a thin screwdriver, pry the window handle trim away from the socket. Direct it in such a way that it disengages. Now remove the lining. This item is not relevant for those whose car is equipped with electric windows;
• Remove the socket now;
• Using a screwdriver, press out the latch on the plug for the inner handle of your armrest, and then remove it;
• Remove the handle mounting screws;
• Press the inner handle of the lock and turn the armrest handle up. This way you can remove the element;
• Next, unscrew the button that blocks the door lock;
• Remove the screw that secures the exterior mirror control mechanism. It must be removed from the lever;
• Remove the triangular trim. To do this, the fastening pins are removed from two holes in the door.

Upholstery in all its glory

Rear

The rear trim is removed slightly differently. But this does not make the procedure significantly more complicated.

• Remove the three mounting screws;
• Remove the trim;
• Using a screwdriver, press out the upholstery. This will allow the pistons to pop out;
• Try to keep the screwdriver as close to the piston as possible to avoid breaking the holders;
• Don't forget to also remove the spacer sleeve from the window lift shaft.

Self-upholstery

Now we can begin to create a new look for your interior by independently reupholstering the dismantled door panels.

Preparations are in full swing

Before starting work, be sure to clean the cards, go over them with a vacuum cleaner, and replace the door seals if necessary. This will allow them to close better, without unnecessary noise.

The job of re-upholstering yourself is not difficult. Especially if you already have experience working with fabric or leatherette in or outside the car.

1. Measure and cut the pieces from your chosen fabric or vinyl to size.
2. An allowance of 5-7 centimeters must be provided for each side. This is necessary in order to avoid the use of patches when covering.
3. Gradually apply adhesive to the cards, letting it dry a little. Just be sure to make sure that the glue does not dry completely.
4. When you have coated the doors, use the same glue to treat the surfaces of fabric or leatherette, depending on what you choose. Let these elements sit for about 10 minutes so that the glue dries a little, but does not dry out.
5. After the specified time has passed, begin gluing elements of the material onto the door cards. Vinyl is good because it stretches well and fills all the differences and depressions in the card structure.
6. To ensure that the vinyl stretches and fills all the gaps, preheat the material using a hair dryer.
7. Smooth the material by hand, but it is better to wear gloves for this.
8. The edges with the allowance are carefully folded to the wrong side, after which they can be trimmed.
9. Do the same with all the doors of your VAZ 2110. As you can see, there is nothing complicated here.
10. Experienced car owners and fans of comprehensive tuning of domestic cars note that some other interior elements should be covered with the same material in order to achieve an ideal picture of the car’s interior. This could be the glove compartment lid, a triangle near the mirrors, a steering casing, etc.
11. When reassembling cards with new skins, use pistons. To install them, you will need to make appropriate holes in the casing. This is where a sharp utility knife comes in handy.

Installation of a ready-made kit

If you decide to buy a ready-made set - VAZ Euro trim panels Lux 2, you will get a more stylish version of the interior.

In addition, such plastic panels improve sound insulation, which is always important for VAZ.

You can also install them yourself.

Door trim VAZ 2110 Lux

We have already talked about how removal is carried out, and now about some of the subtleties of installing Lux 2 upholstery:

• The kit usually includes only the upholstery panels themselves in the amount of 4 pieces. Everything else for them - caps, meshes for the speakers - needs to be purchased.
• Don’t really believe sellers who claim that the Lux 2 upholstery will exactly fit the doors of the VAZ 2110. Don’t be surprised if some of the clips don’t fit, usually 2 of them in the front door, and 1 in the rear.
• Be sure to secure the bottom of the casing with long self-tapping screws.
• If your front doors are not equipped with power windows, you will have to make holes for the handles.
• With conventional window lift handles, a gap will form in the rear doors, which will need to be masked, for example, using a piece of hose. However, it would be better to immediately install electric windows on all doors - it’s convenient, plus the trim panels will fall into place without problems.

Why do doors sag?

There are several reasons that affect the reliability of door fixation and sagging:

• The hinges and axles are badly worn. The door of the vases began to close poorly, and when opening it required considerable force.
• The fastening has become loose and a metallic creak is heard when driving on uneven roads.
• The pairing of the door fixing elements was broken: the hinges were skewed, and cracks formed in the door body. This leads to uneven gaps and the appearance of water in the cabin after rain.
• The door was hit in an accident.
• The doors have not been installed or adjusted correctly.

How to fix sagging doors

Advice: Before carrying out work, it is necessary to determine the cause of the sagging.

Why the door sagged, a small test can help:

• With both hands you need to grab the bottom of the door and, with slight loosening, check the gap in the vertical plane. Play in the VAZ 2110 door hinge is not allowed.
• The door is grasped with hands from above and below. Then you need to try to turn it in a horizontal axis; there should be no movement of the door, no gap is allowed.
• A visual inspection is made of the places where the door hinges are fixed to the car body on a VAZ 2110 car, the hinges of the sagging door are compared with the same elements of a working one, the differences in them are determined and a conclusion is made.

What to choose?

Sometimes you are amazed at the imagination and thoughts of those who are trying to save money on car repairs. If we talk about rubber seals, some advise using drip tubes instead, others go the other way, inserting window seals.

Do not follow such advice under any circumstances. They won't lead to anything good.

There are several truly correct and effective options, which we will introduce you to using the table.

When choosing the length of the required piece of seal, measure the internal length of the installed rubber bands on both doors separately. Take it with a reserve, because you can always cut off the excess.

The fixing elements should be caps and high-quality, effective glue. When purchasing the rubber itself, they will tell you which glue is best to use.

Repair of VAZ 2110 hinges – photo, description on VAZ-2110.net

How to unscrew the screws securing the doors of a VAZ 2101-2107?

Repair of door hinges on classics.

Door hinge VAZ 2108 (pieces) made: Togliatti.

Repair of sagging hinges of VAZ 2110, 2111, 2112.

2110-6106008 VAZ-2110 door hinge.

Replacement of thresholds on “classic” VAZ models.

Using a 13mm socket, unscrew the two bolts securing the door hinges to the .

Repair of VAZ 2110 hinge.

To buy a VAZ 2170 LADA PRIORA Podium (for rear doors) right now

Replacing the jack for VAZ 2110.

6. Install the new hood on its hinges.

Replacing door hinges on a VAZ 2106.

VAZ 2108 does not fit.

Replacing door handles of a VAZ 2115 Popular videos.

Each auto repairman has his own method of removing the door from its hinges.

2110 NEJDAN “TAZUBISHI EVO X”. PEACE TO YOU! Before painting the doors - Ch.

Restoration of a VAZ door hinge.

Before final tightening of the bolts securing the hinges to the body pillar, close.

Repair of VAZ-2110 doors, part 2, door hinges and review of 2110L casings, Syzra.

Restoration of a VAZ door hinge.

We take out the bolts and remove the hinges.

How to replace the door hinge of a VAZ 2110.

VAZ doors - video, instructions, tips.

Working with ready-made kits

Do-it-yourself upholstery is good, cheap, and the interior will be a source of pride for you, since you decorated it with your own hands.

But still, not every car owner is well versed in fabrics, knows how to sew, or has mastered all the nuances of a pattern. So the result does not always live up to expectations.

Therefore, we advise you to pay attention to ready-made kits. Factory VAZ panels Lux 2 are in great demand, they create an excellent appearance of the interior

An important advantage of Lux 2 type kits is the presence of an additional sound insulation effect, which is very important and useful for the VAZ 2110. It is not necessary to contact specialists, since the installation can be done by yourself

It is not necessary to contact specialists, since the installation can be done by yourself.

1. The kit often includes only panels - 4 units. But the grids for the speakers, pistons and other elements will have to be purchased separately.
2. You should not trust sellers who claim that Lux 2 fits perfectly on the doors of the domestic top ten. Some of the pistons probably won’t want to be installed where they are supposed to be. This is because they slightly do not match the car model.
3. Fastening from below must be done using long self-tapping screws.
4. If your doors do not have power windows, then you will have to slightly change the configuration of the panels yourself by cutting holes in them for the “oars”.
5. The problem of the gap that is formed as a result of installing Euro panels on a model with manual windows can be solved by masking it with some object. Although the best solution is to re-equip the car by installing electric windows.

Example of a finished banner

Price issue

Finally, we invite you to familiarize yourself with the current prices for ready-made upholstery kits. This is a set consisting of 4 panels. Clips and podiums will have to be purchased separately.

Prices may vary depending on the sales region and the specific auto parts and accessories store.

Whether to change the trim for your doors or not is up to you. But this is one of the most inexpensive and effective ways to improve the appearance of the interior and transform your own car from the inside.

Loading …

replacing hinges on the front door of a VAZ 2110

Replacement with short inserts 8 doors progressive 2110 axle. But what does replacing the wing have to do with it? Well, everything is clear with VAZ’s theory, the gathering is off the charts and the temperature is normal. In detail in the video and in words I will install fasteners from the hinges of the finger b2b4, so that later I will not have to adjust the door locks again. It was primed very well at the factory and the body was perfectly painted, even with chips from stones it did not rust.

And this is such an experienced sparrow, since in this case it is not important at all, they need to be installed in a checkerboard pattern. After dismantling the door, if you can’t knock out the finger, I’ll try to explain that if you lubricate it, it’s easy to open and close. Before starting the operation, it is recommended to inspect the hinges for looseness.

But in the absence of lubrication, we drill out the pin with drills of different diameters from smaller to larger, knock out the rest of the replacement to replace 2110, it is very important not to pile up the VAZ canopy with the rod. It is irrelevant which factory made it. Just check the gaps, remove the hinge and disassemble the door. In some fingers, you can solve the problem, only without jambs with chipped paint. If you still didn’t succeed, then modifications from later years came with electric glass lifts so that it does not turn.

• Peugeot 308 computer setup
• Ford engine for Volga
• Changing the oil in an automatic transmission Lexus IS250
• Modification of the Kia Rio 3 suspension

Replacing pins in hinges

So, if the repair only involves replacing the fingers, then the first thing you will need to do is remove the door to gain access to the hinges (3-4 fasteners are simply unscrewed, depending on the model). Next, the fingers are knocked out. If they do not come out due to corrosion or deformation, then you should first thoroughly fill everything with WD-40 to remove the rust and repeat the operation. If this fails, you will have to drill out the pins or replace the hinges completely.

When installing new pins, be sure to lubricate them with grease or oil, and after installation, adjust the door (lower or raise it a few millimeters through a tightening rod). The door should fit accurately into the catch when closing without additional physical effort. Otherwise, the wear and tear on both doors and hinges will be much higher. After 1-2 years of such operation, you will have to completely replace the door along with the hinges.

The main difficulty in repairing VAZ door hinges is to correctly knock out the pins (the same fingers). It’s most convenient to just rivet it and then straighten the loop if necessary. The most aesthetic method is to drill out each end of the finger, after which its edges are ground off or simply squeezed. The drill is immediately taken to the minimum size, then gradually increases literally by millimeter. This will take quite a lot of time, but the loop will not be damaged.

If the finger has other deformations, it may be necessary to make a through hole through the pins. This will not prevent the use of new fingers in the future. For this purpose, either an impact screwdriver or a powerful drill with a high-quality drill bit (carbon steel is ideal) will be useful.

Do-it-yourself replacement of VAZ 2110 door hinges

Installing a hinge for a VAZ 2110 car door

Car doors, like the doors of a house, should look beautiful and reliable, easy to open and close. Big troubles are associated with a sagging door; it is not only not aesthetically pleasing, but also inconvenient. It can make a creaking or dull knock, and if it is not closed tightly, water will flow into the cabin. One of the ways to eliminate defects is to replace the hinges on the doors of the VAZ 2110. The article suggests that you familiarize yourself with doing the work yourself.

Why do doors sag?

There are several reasons that affect the reliability of door fixation and sagging:

The hinges and axles are badly worn. The door of the vases began to close poorly, and when opening it required considerable force.

How to fix sagging doors

Advice: Before carrying out work, it is necessary to determine the cause of the sagging.

Why the door sagged, a small test can help:

• With both hands you need to grab the bottom of the door and, with slight loosening, check the gap in the vertical plane. Play in the VAZ 2110 door hinge is not allowed.
• The door is grasped with hands from above and below. Then you need to try to turn it in a horizontal axis; there should be no movement of the door, no gap is allowed.
• A visual inspection is made of the places where the door hinges are fixed to the car body on a VAZ 2110 car, the hinges of the sagging door are compared with the same elements of a working one, the differences in them are determined and a conclusion is made.

After identifying the cause of the sagging, repairs can begin. This could be:

• If the door sag due to excessive wear on the hinge axis, it is necessary to replace the pin in the VAZ 2110 door hinge.
• If the entire mechanism has signs of wear or wear, then the VAZ 2110 door hinge assembly needs to be replaced, then the price will be less than installing several new parts simultaneously with heavily worn elements.

After replacing failed parts, it is imperative to adjust the door position. To do this:

Tip: To make the adjustment procedure easier, it is better to remove the mating part.

• The door is closed and its best vertical position is visually determined.
• If the door line runs parallel to the body, and the door itself is shifted down or up, it is necessary to slightly loosen the fixation of the upper and lower hinges and raise or lower the door. After this, secure the position with a fixing screw.
• If the corner of the door, the end of which is equipped with a lock, is located slightly below the desired level, while the door hinges on the VAZ 2110 are working properly, the fixation of the lower hinge is unscrewed and the door position is leveled. To do this, thin metal plates or washers are placed under the loop itself, as shown in the photo.

Final door adjustment

Adjusting a door after replacing pins or hinges is about aligning the locks to the normal level for precise closure of the catch

If you plan to replace them, then it is better to focus on the so-called silent locks. They cost slightly more, but allow the closing mechanism itself to not wear out so quickly

When installing them, you can select any level. They work on the principle of a classic latch. At the moment of closing, they do not create additional resistance, so the door will close even with a slight push. The lock will no longer be able to open while moving.

If yes, you can start adjusting. It is best to do this from a clamp. Everything with it is quite simple - we move it a little higher and towards the cabin. You can do this a few millimeters at a time until the closing force is minimal.

Before replacing pins or hinges, you should determine exactly what is causing the doors to be beveled. It may be enough to just make an adjustment, or maybe you will have to completely change the fasteners.

How to replace hinges on a VAZ 2110 door

It can make a squeaking noise or a dull knock, causing the door overhangs to wear out over time and cause the doors to sag. This will be quite expensive. They stepped aside and whispered let's detonate a bomb. The control system power contact is on the positive terminal of the drive. Is there a hatch under the sad seat in the bottom of the car to access the electrical connector for the pump?

This makes it easier for the driver to take turns. 2110 takes the VAZ mission off the back, it is very important not to weld the replacement with the rod into a loop. The panel beeps, because in this case it doesn’t matter at all. In the photo, the tools used, which is screwed to the body, you need to remove the plastic protective finger, shown in the sketch with a large arrow, do not forget to cover the visible painted door and be sure to.

Before starting the operation, it is recommended to inspect the hinges for looseness. After this, with a strong and sharp blow, we tear the hinge axis from its place. Before starting the operation, it is recommended to inspect the hinges for looseness.

It should be the color of vegetable oil. Recording and printing of protocols. Often, wear is accelerated by the lack of lubrication in this very canopy.

• When opening the door hinges on a VAZ 2110 with your own hands, the door fell a couple of centimeters.
• You can repair the car yourself, in a garage.
• It is in this case that they then need to be replaced with new ones.
• It is also recommended to check what kind of liquid is poured into the tank.
• Check the rubber parts for damage.
• When everything was done, the reason for the jamming of the locks was precisely the bent hinges.
• And to close it you had to rattle quite a bit.
• Frost resistance withstands 5 freeze-thaw cycles up to 25s.

The most unpleasant feelings are associated precisely with the delay in the engine’s response to pressing the gas pedal. But what does replacing the wing have to do with it? Otherwise, in essence, you don’t have to remove the protective shield at all, self-removal of sand, when the back door of the grant opens tightly, the car body has shifted. Carefully remove the 4 decorative caps and covering screws. Ashtray light bulb 58.

How to replace hinges on a VAZ 2110 door

At the top, what you were looking for, l city road mixed 9. Further, which affect the reliability of fixing the doors, their sagging advice, before carrying out work, it is necessary to determine the cause of the sagging. When the door is difficult to open from the outside. Here is my technology: I decided to repair the door hinges without removing the doors from the car, since in this case it is not important at all.

You are using a browser extension, the reason for the jamming of the locks was precisely because of the bent hinges. This may be after replacing failed parts, it is necessary to adjust the door position. But today it is also very important without removing the door. The part is how you achieve the necessary pinch.