Installing seat belts on a VAZ 2106 motors-avto.su

Installing seat belts on a VAZ 2106

If you are involved in an accident, then after it you will not only have to carry out body repairs, but also change the deployed airbags along with the belts, or only the latter, since your car may not have airbags.
But even if you have never been in an accident in your entire driving experience, seat belts (SB) can become unusable, simply wearing out and losing strength over many years of service, after which they need to be replaced with new ones. Below you will learn how to do this on a VAZ-2106 car. Content:

You will need a minimum of tools: a flat-head screwdriver and a 17mm wrench or socket wrench. Well, a new belt and its lock, of course.

Replacing front seat belts on a VAZ 2106

The diagram shows the location of the belt: number 1 is the reel, number 2 is the belt itself, 3 is the latch, and 4 is the loop.

1) Take a screwdriver and use it to carefully pry the cover on the hinge mounting bolt.

2) Remove the trim, being careful not to damage its clips.

3) Take the key and unscrew the bolt that secures the RB hinge.

4) After removing the hinge, try to put it somewhere in a visible place so that the small parts associated with it do not get lost.

5) Arm yourself with a screwdriver again and remove the cover, but this time on the coil.

6) Unscrew its mounting bolt, being careful not to lose the washer and spacer.

7) Remove the coil.

Take the new belt and install it in place of the old one.

After installation, it is important to check the smooth movement of the belt so that it can be pulled out and retracted without hindrance. If there are problems with this, you need to adjust the position of the reel so that the slot in it is horizontal in relation to the belt, and not at an angle.

You also need to check whether the reel is defective: normally, when jerking, the belt should not move, but when pulling smoothly, on the contrary, it should. If the coil does not work normally, it should be exchanged for another one at the store.

Usually, along with the belt, its lock, located between the front seats, also changes.

To replace it you should:

Remove the cover on the mounting bolt.

Unscrew the bolt, removing the sleeve and washer, after which the lock will be removed.
Install a new lock.

How to change rear belts and their locks on a VAZ 2106

Rear belts usually last longer than front ones, but they don’t last forever. The tools are the same, but to replace it you will first have to remove the back of the rear sofa. Further:

1) Use a screwdriver to pry up the cover and then remove it.

2) Unscrew the mounting bolt located at the bottom.

3) Repeat step 1 for the top fastening, exactly like step 3.

6) Then unscrew the bolt securing the hinge, and then remove it with its associated small parts.

7) Now it's the turn of the coil bolt.

Next you need to pry up and remove the RB guide.

9) Pass the belt assembly with guide and loop through the slot in the rear pillar trim panel.

10) Dismantle it, after which you can install a new RB.

Replacing locks is done as follows:

The back row of the back row is removed (if you have not done this earlier).
The mounting bolts are unscrewed

After which the locks can be easily removed and replaced with new ones.

In conclusion, it should be noted that if you also want to change all the bolts securing the hinges, locks and coils, then you should buy new ones only at a car dealership, since these are specialized parts that can withstand high loads. It is strictly forbidden to install ordinary bolts, since in the event of an accident they will be cut off, which will lead to a sad outcome.

Source: avtgid.ru

The procedure for dismantling and installing the front belts of the VAZ 2106

You should consider in detail the algorithm for replacing the front seat belts on a VAZ 2106 car. To do this, you need to prepare the following tools:

flat screwdriver;

wrench 17.

Each of these types of front belts must be removed from a VAZ 2106 in the following order:

Using a flat-head screwdriver, carefully pry and remove the decorative trim located on the top hinge mounting bolt.

New safety devices must be installed in reverse order. Installing a new coil can be somewhat difficult. To do everything correctly when carrying out work, it is necessary to ensure that the slot of the inertial reel releasing the retaining device web is positioned strictly horizontally in relation to it. If you suddenly installed the coil without following the specified rule, then in the future the mechanism may perform poorly.

When installing a new device, the locks located between the front seats are usually changed. To do this you need to do the following:

remove the decorative trim by prying it off with a flat screwdriver;
Unscrew the fastening bolt with a 17 mm wrench, remove the washer and bushing;
remove the old lock;
install a new lock, performing all the steps in reverse order.

Read more: Necessary evidence in the arbitration process

In order for the newly installed mechanism to fully perform its assigned functions, it is necessary to use only specialized elements.

Rear seat belt function

The main purpose of seat belts (SB) is to provide reliable protection for the driver and passengers in the event of an accident. You should fasten your seat belt before you start driving, including when moving around the city. Not only the driver, but also the passengers must buckle up.

Unbelted rear passengers create an additional threat to the life of the driver and themselves in the event of emergency braking.

There are rules for using RB:

You cannot fasten several passengers with one seat belt;
It is prohibited to restrain a child sitting in the arms of a rear passenger;
There should be no objects between the person’s body and the belt that could
injure the body in emergency situations;
The RBs should be smooth, without twisted places, and well tensioned.

Large amounts of clothing create bulk, which reduces protection.

For the rear seats, as well as for the front ones, three-point, self-winding RBs are installed. They are mounted on the side of the body. In the middle of the rear seat there is only a two-point lap belt, the length of which can be set manually. You can install rear non-inertial RBs, but they are inconvenient to use, since they have to be wound up manually each time.

How to install rear seat belts on a VAZ 2106 yourself?

A car is a place where a person is often in danger. Therefore, modern cars are equipped with various systems and means that increase the safety of the driver and passengers. These devices include seat belts. In early versions of VAZ 2106 cars, rear belts were not installed at the factory, although fastenings were provided for them. The article describes: the purpose of rear seat belts, how to install them yourself on a VAZ 2106.

Rear seat belt function

Unbelted rear passengers create an additional threat to the life of the driver and themselves in the event of emergency braking.

There are rules for using RB:

You cannot fasten several passengers with one seat belt;
It is prohibited to restrain a child sitting in the arms of a rear passenger;
There should be no objects between the human body and the belt that could injure the body in emergency situations;
The RBs should be smooth, without twisted places, and well tensioned.

Large amounts of clothing create bulk, which reduces protection.

Rear seat belts

We change it ourselves

If the RBs experienced a shock load during an accident, they must be replaced along with the winding device. The service life of these products on the VAZ 2106 is 10 years. During operation, belts rub, fray and stretch, so it is necessary to monitor their condition. They must be clean, elastic, without damage or abrasions. If defects are found, parts should be replaced.

A set of necessary tools

To install the RB on a VAZ 2106, you need to prepare:

a set of keys:
screwdriver;
inertial RB;
fastenings;
fasteners.

You should buy RB in a vertical version. True, you will have to suffer a little with their installation.

Stages

Installing rear seat belts on a VAZ 2106 consists of the following steps:

First you need to open the trunk of the car.

Open car trunk Next, we find a suitable hole in the side wall of the VAZ 2106 body, which is provided from the factory. We drill the hole to the bolt with a “10” thread.

Enlarged hole for bolt thread

Next, you need to insert the bolt into the hole and screw it as tightly as possible with a nut. In this case, a large washer should be placed on the cab side so that the bolt head does not cut into it.
We put the RB coil on the bolt and secure it with two nuts: internal and external.

Procedure for dismantling and installing rear elements

Rear seat belts are generally more durable than front seat belts. But from time to time you have to replace them too.

When dismantling and installing these mechanisms at the rear, use the tools mentioned above. The procedure for dismantling them is as follows:

First, the rear seat backrest is removed.
Using a flat-head screwdriver, remove the decorative covers of the mounting bolts at the top and bottom.
Then the bolts themselves are unscrewed along with the lower and upper fasteners.
Carefully remove the coil and guide.
To completely dismantle the old device, you need to insert it together with the hinge and guide into the slot in the rear pillar trim panel.

Then you can replace the old lock with a new one. To do this, you need to unscrew the mounting bolts and easily remove the old locks. Please note that this work is performed with the rear seat backrest removed. New rear security devices and locks are installed in exactly the reverse order.

An important stage in carrying out this type of work is checking the correct installation of the mechanisms. When moving smoothly, the belt should move freely, be easily secured in the lock, and when jerked, it should be sharply fixed in a certain position.

Installing seat belts on a VAZ 2106

If you are involved in an accident, then after it you will not only have to carry out body repairs, but also change the deployed airbags along with the belts, or only the latter, since your car may not have airbags. But even if you have never been in an accident in your entire driving experience, seat belts (SB) can become unusable, simply wearing out and losing strength over many years of service, after which they need to be replaced with new ones. Below you will learn how to do this on a VAZ-2106 car.

Content:

You will need a minimum of tools: a flat-head screwdriver and a 17mm wrench or socket wrench. Well, a new belt and its lock, of course.

Replacing front seat belts on a VAZ 2106

The diagram shows the location of the belt: number 1 is the reel, number 2 is the belt itself, 3 is the latch, and 4 is the loop.

1) Take a screwdriver and use it to carefully pry the cover on the hinge mounting bolt.

2) Remove the trim, being careful not to damage its clips.

3) Take the key and unscrew the bolt that secures the RB hinge.

4) After removing the hinge, try to put it somewhere in a visible place so that the small parts associated with it do not get lost.

5) Arm yourself with a screwdriver again and remove the cover, but this time on the coil.

6) Unscrew its mounting bolt, being careful not to lose the washer and spacer.

7) Remove the coil.

Take the new belt and install it in place of the old one.

Usually, along with the belt, its lock, located between the front seats, also changes.

To replace it you should:

Remove the cover on the mounting bolt.

Unscrew the bolt, removing the sleeve and washer, after which the lock will be removed.
Install a new lock.

How to change rear belts and their locks on a VAZ 2106

Rear belts usually last longer than front ones, but they don’t last forever. The tools are the same, but to replace it you will first have to remove the back of the rear sofa. Further:

1) Use a screwdriver to pry up the cover and then remove it.

2) Unscrew the mounting bolt located at the bottom.

3) Repeat step 1 for the top fastening, exactly like step 3.

6) Then unscrew the bolt securing the hinge, and then remove it with its associated small parts.

7) Now it's the turn of the coil bolt.

Next you need to pry up and remove the RB guide.

9) Pass the belt assembly with guide and loop through the slot in the rear pillar trim panel.

10) Dismantle it, after which you can install a new RB.

Replacing locks is done as follows:

The back row of the back row is removed (if you have not done this earlier).
The mounting bolts are unscrewed

After which the locks can be easily removed and replaced with new ones.

What will be required for repairs?

For the reasons mentioned above, sometimes the seat belt does not extend. What to do? Advice from experienced auto mechanics will help. First of all, you will have to disassemble the casing and remove the coil. In some models, you will have to dismantle the seats in the place where the breakdown occurred.

Repairs can be simple or more complex. In some cases, you have to completely change the coil. For some machine models, you will need to prepare special tools. But repairing a seat belt yourself will help save quite a lot of money in the family budget.

Tools

To disable the lock if a corresponding signal appears, the entire mechanism will need to be cleaned. To do this, you need to thoroughly prepare in advance and collect all the necessary tools. so what to prepare:

a Phillips screwdriver, preferably a short one;
flat head screwdriver;
a wrench set to “17”, it will be more convenient to use a socket wrench;
stationery pin;
syringe with tube;
some gasoline (lighter fuel is ideal).

Read, it may come in handy: How to replace a broken headlight glass

Phillips head screwdriver. Screwdriver with slotted tip 17mm wrench Stationery pin for fixing Syringe with tube Gasoline for lighters